Cymatics · Chladni, Faraday, Lissajous
Cymatics: The geometryof sound.
Pick a frequency or a sound from the Library: on the vibrating plate, sand migrates to the lines that never move.
0.0Hz
Mathematical visualization · not a measurement
24 × 24 cm · 0.90 mm aluminium
Driven at the centre
λ = ωa²√(ρh/D) = 0.00 · Q 200 · SLOW MOTION ×4
01 · Source
Sine · keep the volume low
02 · Frequency
Tick: excited mode · height: coupling
Frequency sweep · modes
100-3,000 Hz
03 · View
Sand jumps off vibrating areas and stops on the lines where the acceleration stays below gravity.
04 · Plate
Thickness shifts every mode proportionally (f ∝ h). Driven at the centre (as in demonstration kits), modes symmetric about both axes and diagonals are excited strongly; the driver sits 1% off centre, so the others appear faintly.
05 · Drive
Γ 9.2 g
The strength of the vibration (acceleration at resonance). Brightness never changes; at higher drive the lines get thinner and the pattern settles faster.
What are you seeing?
01
Nodal lines
On a vibrating plate some lines never move. Sand jumps off where the acceleration exceeds gravity and stops in the thin strip where it does not. The pattern is a map of where there is no motion.
02
Mode and frequency
A plate vibrates strongly only at the frequencies of its own modes (resonance). In between, the acceleration falls and the sand stays still. The modes come from the thin-plate equation: frequency rises with thickness and falls with the square of the side length.
03
Mathematics, not measurement
The patterns are drawn from equations; they are not measurements of a real plate. Nor is a pattern the single shape of a sound: the same sound looks different on another plate, dish, depth or light. For Library sounds, the pattern is built from the peaks of the sound's measured spectrum.
Sources: E. F. F. Chladni, Entdeckungen über die Theorie des Klanges (1787); W. Ritz (1909), free square plate; A. W. Leissa, Vibration of Plates, NASA SP-160 (1969); M. Faraday, Phil. Trans. 121 (1831); Abramian et al., Phys. Rev. Research 7, L032001 (2025), sand dynamics; Chen and Viñals, Phys. Rev. E 60 (1999), Faraday pattern selection; Miles and Henderson, Annu. Rev. Fluid Mech. 22 (1990).
What does sound look like on a vibrating plate?
Cymatics drives a vibrating plate with a single frequency or with any sound from the Library and shows where the sand gathers: Chladni patterns. Square and circular plates are computed from the real thin-plate equation (free edges, Ritz method and Bessel modes), the water surface from Faraday waves and Lissajous figures from two perpendicular vibrations. It is a mathematical visualization of sound, not a measurement of a physical plate.
How do you use Cymatics?
- Choose a form: square plate, circular plate, water surface or Lissajous.
- Choose a source: a single tone or a sound from the Library. With a sound, the pattern is built from its spectral peaks.
- With a tone, slide the frequency or step through the plate's modes with ‹ Previous mode and Next mode ›; the ruler snaps to the nearest mode.
- Press Play (keep the volume low). Sand jumps off vibrating areas and collects on the nodal lines.
- Switch the view (sand, lines, wave, 3D surface) and turn the nodal line layer on or off; drag the 3D surface to rotate it.
- Start the sweep: the frequency moves from 100 Hz to 3 kHz in 40 s; the pattern turns from mode to mode, and the strip shows the modes' resonances.
- Export the image as PNG or SVG.
What is it used for?
Browse Chladni patterns
With a single tone, step through the modes of the square or round plate with the previous and next mode buttons; the sand gathers on the nodal lines.
Show vibration in a lesson
Start the sweep: the frequency moves from 100 Hz to 3 kHz in 40 seconds and the pattern changes from mode to mode; a good demonstration for a lesson on vibration and resonance.
Visualise sounds from the Library
Pick a sound from the Library as the source; the pattern is built from the sound's spectral peaks. The image is mathematical, not a measurement of a real plate.
Export the pattern
Choose a view (sand, lines, waves, 3D surface) and export it as PNG or SVG; you can use it on a poster or in a presentation.
How to read the results
- On a plate, if Acceleration is below 1 g you see 'sand at rest': the plate is not resonating at this frequency. With a single tone, move to a mode with Next mode › or raise 05 · Drive. In the SAND view 'sand jumping' turns into 'pattern settled' in about 8-10 s.
- On the square plate a mode name such as (1, 2)+ counts the nodal lines along x and y; the sign says whether the mode is added to (+) or subtracted from (−) its twin (2, 1). On the circular plate the name counts diameters and circles.
- On the frequency ruler the ticks are the plate's excited modes and their height is the coupling to the drive point. With a Library sound the clay-coloured bars are the sound's spectral peaks and the large number is the strongest peak; Fit the plate to the sound puts that peak on a mode.
- On the water surface the wave runs at half the drive frequency; 'Wave growing' turns into 'Wave saturated · pattern settled' in about 6 s. In Lissajous, if Detuning is above 0 Hz the figure turns at that rate, at most 0.1 Hz on screen.
- The pattern is drawn from equations: it is not a measurement of a real plate, nor the one shape of the sound. The same sound looks different on another plate, thickness or dish.
Forms
| Form | Model | What you see |
|---|---|---|
| Square plate | Thin plate with free edges, Ritz method (24 cm, 0.9 mm aluminium) | Chladni's classic curved lines; pairs (m, n) ± (n, m) |
| Circular plate | Free edge, exact solution with J and I Bessel functions | Rings when driven at the centre, diameters when driven at the edge |
| Water surface | Faraday waves: the wave at half the drive frequency, capillary–gravity dispersion | Mandalas in a small dish; squares, hexagons and quasi-patterns on a wide surface |
| Lissajous | Two perpendicular simple harmonic motions | The figure of the ratio; it turns slowly when the ratio is not exact |
Why does sand gather on lines?
Some lines of a vibrating plate never move: the nodal lines. Where the plate's acceleration exceeds gravity, sand jumps; the jumps grow longer as the acceleration rises. Randomly hopping grains end up where the jumps are shortest, on the nodal lines. Ernst Chladni showed this with a violin bow in 1787; the grains' motion was measured in 2025 (Abramian et al.).
A plate vibrates strongly only at the frequencies of its own modes. Between two modes the acceleration falls and the sand stays still, so while sweeping the frequency a pattern appears only at resonances. The frequency rises with thickness and falls with the square of the side length.
Is this a measurement?
No. The patterns are drawn from equations. On a real plate, material flaws, the driver's mass and the sand itself shift the frequencies. Nor is a pattern the single shape of a sound: the same sound looks different on another plate, dish, depth or light.
Frequently asked questions
- How is the pattern of a Library sound built?
- The strongest peaks of the sound's long-term spectrum (up to eight) drive the plate together; each peak excites the modes near it. While the sound plays, the pattern updates from the shared player's live spectrum. Fit the plate to the sound picks the thickness that puts the strongest peak on a mode.
- Why doesn't the sand move at some frequencies?
- The plate is not at resonance at that frequency: its acceleration stays below gravity. In real demonstrations, too, sand only jumps at the modes. The ruler snaps to the nearest mode; the ‹ Previous mode and Next mode › buttons go straight to the modes.
- Why is the water pattern at half the drive frequency?
- In a vibrating liquid, surface waves are excited parametrically (Faraday 1831): the strongest response is at half the drive frequency. Gravity and surface tension set the wavelength; the bright lines are where the surface's slope reflects the light.
- How can I use the image?
- The PNG is 2048 × 2048 pixels; the SVG is a vector drawing of the nodal lines. The files are made on your device and are not sent anywhere.
Listen and try
· v1.15 · changelog