02 / Explore · Tools05 / Menu · Tools

Tone generator

Pure tones and frequency sweeps. Start quiet and turn up slowly.

Tone generator

440 Hz · A4

Hz

On the slider, Shift + arrow key steps 0.01 Hz; the number box accepts both comma and dot.

Waveform
dB

Frequency sweep

A tone gliding between two frequencies, to hear which range your headphones or speaker reproduce comfortably. Not a session.

Hz
Hz
for 30 s

How do I play a specific frequency?

The tone generator plays a pure sine or triangle wave between 20 Hz and 20 kHz; the frequency changes in 0.01 Hz steps and live while playing, and the ×½ and ×2 buttons jump an octave. The frequency sweep walks from a start to an end frequency logarithmically (each octave takes the same time) over 2 seconds to 10 minutes. The sound is generated on your device; above 4 kHz the level is cut by 12 dB.

How to use the tone generator

  1. Type the frequency or pick it with the slider (e.g. 440 Hz); jump octaves with ×½ and ×2, set the waveform to Sine or Triangle.
  2. Start at a low level (−30 dB is the default) and press Play; you can change the frequency while playing, the transition is smoothed over 50 ms.
  3. In Frequency sweep, enter the start, end and duration (2 s-10 min) and press Start sweep to hear the frequency walk octave by octave.
  4. The settings live in the address (?hz=528&db=-30&dalga=sinus): sharing the link opens the same tone.

What is it used for?

  • Find your speaker's bass limit by ear

    Type 100 Hz and slide slowly down to 20 Hz; the point where the tone disappears gives a rough idea of how low the playing device goes. This is a listening test, not a measurement; for a measurement there is the Approximate response measurement.

  • Get octaves and intervals into your ear

    Play 440 Hz, then go up an octave with ×2: the pitch changes but the note stays the same. Listening to 440 and 660 Hz one after the other lets you hear the 3:2 ratio of a pure fifth.

  • Demonstrate it in a physics or music lesson

    Change the tone while it plays to show how frequency relates to pitch; the TONE line in the Lens panel shows the playing frequency to two decimals. The settings are kept in the address, so sharing the link opens the same tone for your students.

  • Look for your room's boomy bass

    Set the logarithmic sweep to 40-200 Hz over 60 seconds: in a room some frequencies swell and others fade. Note the bands that swell, then move the speaker and compare.

How to read the results

  • The TONE row of the Lens panel shows the playing frequency to two decimals; the resolution beside it is the smallest difference the display can separate, not the accuracy of the sound.
  • Not hearing a frequency doesn't mean it isn't playing: small speakers and headphones are weak below 40 Hz, and not hearing above 12 kHz is common with age.
  • During a sweep, bands where the sound dips or swells are the response of your headphones, speaker or room; to measure that, use the approximate response measurement.
  • Above 4 kHz the engine lowers the level by 12 dB: a quieter high frequency is a safety limit, not a fault.

Limits

Values from the audio engine's limit table; the limiter and the fade-in are active for every tone.
SettingRangeNote
Frequency20 Hz-20 kHz0.01 Hz steps; warning above 12 kHz
Level−60 to −12 dBan extra −12 dB ceiling above 4 kHz
Wavesine · triangletriangle adds odd harmonics at 1/n²
Sweep2 s-10 minlogarithmic: every octave takes the same time

Sine and triangle

A sine carries a single frequency; it has no timbre, only pitch. A triangle wave adds the odd harmonics (3f, 5f, 7f…) to the same pitch with amplitudes falling as 1/n²: a fuller yet still soft sound. When testing whether you 'hear' a frequency, use the sine; with the triangle the upper harmonics can be audible even when the fundamental is not.

High frequencies can tire quickly; the engine cuts the level by 12 dB above 4 kHz and warns above 12 kHz. Not hearing above 12 kHz is common with age; don't search for it by turning the volume up, the generator's level limit is −12 dB.

What is the sweep for?

A logarithmic sweep gives every octave the same time: from 20 to 20,000 Hz is ten octaves, so a 100-second sweep spends 10 seconds per octave. It suits searching by ear for the resonances of a speaker or a room, noticing in which band a pair of headphones weakens, and use together with the Spectrum analyser. A sweep is not a measurement; for that there is the Approximate response measurement.

Frequently asked questions

Does a particular frequency have an effect?
The generator is a tool and makes no claim (○ S). The state of evidence for effects attributed to frequencies such as 432, 528 or 40 Hz is written in the related articles and evidence cards.
I can't hear a very low frequency.
Small earphones and speakers reproduce 20-40 Hz weakly; what you hear is often the harmonics of the triangle wave. Switch to the sine and set your expectation accordingly.
I heard a click.
Frequency changes are smoothed over 50 ms and the output passes through the limiter; a click usually comes from the device's audio path or a Bluetooth switch. Try a short pause between stop and start.

· v1.15 · changelog

No cookies, no tracking. Details: Privacy notice (KVKK) On-device storage