Wave Interference
Add three waves and shift one's phase: in phase they reinforce, in opposite phase they fade to silence. Close frequencies beat, ratios draw Lissajous figures, and two sources build nodal lines in water.
Wave Interference
PRESET EXPERIMENTS
TAPWAVES
f · A · φA beat above 2 Hz plays only after the safety confirmation (the Beat generator's band); up to 2 Hz always. The display is slowed down: the dial and the figure turn at ≤ 0.5 Hz.
What is happening?
A AND B- PHASE DIFFERENCE (B − A)
- 0°
- TOTAL AMPLITUDE
- 1.60 · constructive
- BEATS
- none
- RATIO B : A
- 1 : 1
CALCULATION · SUM OF TWO SINES: 2A·cos(Δφ/2) · BEAT |f₁ − f₂|
Five faces of interference
SEE IT HERE- Constructivetwo waves in phase: the amplitudes add
- Destructive180° apart: they cancel each other
- Beatclose frequencies: swells |f₁ − f₂| times a second
- Lissajoustwo perpendicular vibrations: the ratio chooses the figure's shape
- Nodal linedifference in distance to the two sources is half a wavelength
What happens when two waves meet?
Wave Interference is a simulator that adds three sine waves and lets you both hear and see the result. Two waves at the same frequency and in phase reinforce each other; 180° apart they cancel. Close frequencies beat: 220 and 223 Hz swell and fade three times a second. Ratios draw Lissajous figures, and a two-source ripple tank shows the nodal lines of interference.
How does Wave Interference work?
- Choose Constructive from the presets and press Listen: two equal waves add in phase and the amplitude doubles.
- Switch to Destructive or move B's phase slider to 180°: the sum fades to silence. The Shift phase button slowly rotates B's phase.
- In the Beat preset two close frequencies swell |f₁ − f₂| times a second; a beat above 2 Hz asks for confirmation first.
- In the Octave, Fifth and Chord presets the frequency ratio chooses the shape of the Lissajous figure.
- Change the source spacing in the ripple tank: the wider the spacing, the more nodal lines.
What is it used for?
Hear constructive and destructive interference
Add two equal waves in phase and the amplitude doubles; set B's phase to 180° and the sum fades to silence.
Demonstrate beats
Two close frequencies swell and fade |f₁ − f₂| times a second: 220 and 223 Hz three times a second.
See ratios as Lissajous figures
In the octave, fifth and chord experiments the frequency ratio sets the shape of the Lissajous figure; simple ratios give simple figures.
Nodal lines in the ripple tank
In the two-source ripple tank, the number of nodal lines grows as you widen the gap between the sources; a good visual for explaining interference in a physics lesson.
How to read the results
- TOTAL AMPLITUDE 2.00× · constructive means equal A and B add in phase; 0.00× · destructive means they cancel 180° apart; in between it reads partial. This line only appears when A and B share a frequency.
- The Hz on the BEATS line is how many times a second the sound swells and fades: the smallest difference |f₁ − f₂| between active waves. Above 40 Hz it shows —; above 2 Hz GATE appears and the sound starts only after Confirm and listen.
- The ratio next to LISSAJOUS · A × B is B's nearest simple ratio to A (numbers up to 9). If it says APPROXIMATE the ratio is not exact and the figure turns slowly; with an exact ratio the figure closes and stands still.
- In the ripple tank, light bands are constructive and dark lines are nodes. The NODAL LINES count grows with the source spacing: 0 at 0.5 λ, 6 at 3 λ. The tank is a model; what you hear is the sum at a single point.
- DISPLAY 1/N SPEED tells you how many times slower than real the waves are drawn (at least 200 times); the screen never flashes at the beat rate.
Six presets
| Preset | Waves | What you hear |
|---|---|---|
| Constructive | 220 + 220 Hz, in phase | One tone, double amplitude |
| Destructive | 220 + 220 Hz, 180° apart | Silence |
| Beat | 220 + 223 Hz | A tone that swells three times a second |
| Octave | 220 + 440 Hz | 2 : 1, two voices that blend |
| Fifth | 220 + 330 Hz, B at 90° | 3 : 2, a Lissajous figure |
| Chord | 220 + 275 + 330 Hz | 4 : 5 : 6, a major triad |
Superposition
When two waves meet in the same place they add: at every moment the sum of the two heights is the new wave. The combined amplitude of two waves at the same frequency depends on their phase difference: in phase the amplitudes add, 180° apart they subtract. For two waves of equal amplitude the sum is 2A·cos(Δφ/2); at Δφ = 180° this is zero.
In the tool the time axis draws the three waves faintly and their sum boldly; the phasor dial shows each wave as an arrow and joins the arrows end to end. The length of the sum can be read on the dial.
Beats, ratios and nodal lines
Two waves of slightly different frequency meet now in phase, now in opposite phase. The amplitude of the sum rises and falls |f₁ − f₂| times a second: this is called a beat. The tool draws the beat envelope in a one-second window that drifts slowly; the screen never flashes at the beat rate.
When the frequencies form a simple ratio (2 : 1, 3 : 2) the curve traced by two perpendicular vibrations closes and the Lissajous figure stands still. In a two-source ripple tank the waves cancel wherever the difference in distance to the sources is an odd multiple of half a wavelength; these points form the nodal lines.
Frequently asked questions
- Where does the energy go in destructive interference?
- It is not lost. The waves cancel at the silent point and reinforce elsewhere; the light and dark bands in the ripple tank show this. The sound in the tool is the sum at a single point.
- Why does a beat ask for confirmation?
- A beat above 2 Hz lies inside the band the Beat generator plays. Every sound in that band follows the same path on the site: the sound starts after you confirm. 2 Hz and below is free.
- Is this a binaural beat?
- No. Here the two waves are added in the same channel and the beat happens in the air, so it is heard through speakers too; this is called a monaural beat. In a binaural beat each ear hears a separate tone; you can try that in the Binaural beat generator.
Listen and try
· v1.15 · changelog