02 / Explore · Tools05 / Menu · Tools

Tone balance

Balance noise for your own headphones and ears. Not a hearing test.

Listen to the bands one by one

  1. Put on your headphones and set your device volume to a comfortable listening level; don't change it during the test.
  2. Each band starts at its quietest. Slowly raise the level and stop as soon as you first hear the hiss.
  3. Mark it with "I hear it here" and move to the next band.

Band 1/10 · 31.5 Hz

dB

If you can still hear the quietest setting, turn your device volume down a little and try this band again.

Band thresholds
BandFirst heardSuggested tone balance
31.5 Hz——
63 Hz——
125 Hz——
250 Hz——
500 Hz——
1 kHz——
2 kHz——
4 kHz——
8 kHz——
16 kHz——

This is not a hearing test and tells you nothing about your hearing. Together with your headphones, device settings and background noise, the result only serves to make the tonal balance of noise more comfortable for you. Values are file levels (dBFS), not the sound level reaching your ears.

Is the noise balanced on my headphones?

Tone calibration opens the ten octave bands of noise (31.5 Hz to 16 kHz) one by one from the quietest level, lets you mark the level at which you first hear each, and derives from those thresholds a noise tone balance for your headphones and your ears: bands with a threshold above the average are boosted by half the difference, bands below are cut, within ±12 dB. The profile is stored only on this device. This is not a hearing test.

How to use tone calibration

  1. Put on your headphones, set the device volume to your usual level in a quiet place; interface sounds are muted while the tool is open.
  2. Press Play band: the band starts at the quietest level (−60 dB); raise the Level slider slowly until the moment you first hear it and press 'This is where I hear it'.
  3. Complete the ten bands with Next band ▶; the table shows each band's first-heard level and the suggested tone setting.
  4. Save the profile to this device; if you like, 'Apply to noise in the Room' makes the noise layer in the Listening room play with this balance.

What is it used for?

  • Balance noise for your headphones

    Mark the level where you first hear each of the ten bands; from these thresholds the tool derives a noise tone balance for your headphones (±12 dB).

  • Apply it to noise in the room

    Save the profile on this device and use Apply to noise in the room to play the Listening room's noise layer with this balance.

  • See how headphones differ

    Run the setup with two headphones in turn and note the thresholds in the table to see in which bands they differ.

  • Know what is not measured

    The thresholds are the combined result of your headphones, your device's volume and your ears; this is not a hearing test, and if you have concerns about your hearing, see a specialist.

How to read the results

  • The 'Band 3/10 · 125 Hz' line shows the octave band you are listening to (31.5 Hz to 16 kHz). The First heard column is the level you marked, between −60 and −12 dB: the lower the number, the more easily that band was heard on these headphones.
  • The Suggested tone balance is half the difference between a band's threshold and the average of all ten bands (0.5 dB steps, ±12 dB): plus boosts the band, minus cuts it. A threshold 8 dB above the average becomes +4 dB. The column fills once all ten bands are marked.
  • If the low bands (31.5 and 63 Hz) come out high, it is usually small headphones or background noise. If you can still hear the quietest level, turn your device volume down a little and try the band again.
  • The values are file levels (dBFS), not the level reaching your ears. The result is not a hearing test and tells you nothing about your hearing.
  • The Saved profile line gives the date you saved it and the ten band settings from low to high. The profile doesn't carry over to other headphones; redo it when you change them.

Bands and the setting rule

Octave centres; each band is pink noise passed through a one-octave band-pass filter. Setting = (threshold − mean) × ½, 0.5 dB steps, ±12 dB limit.
Band centreThreshold above the meanThreshold below the mean
31.5 · 63 · 125 Hzband boostedband cut
250 · 500 Hz · 1 kHzband boostedband cut
2 · 4 · 8 · 16 kHzband boostedband cut

What does the threshold measure?

The first-heard level is the sum of three things: the headphones' efficiency in that band, the device's volume setting and your sensitivity at that moment. That is why the result is not a hearing measurement and is invalid on other headphones; room noise also raises the thresholds of the low bands. The profile roughly balances the bands that reach your ear weakly, but applies only half the difference, because a difference at threshold is not the same size at normal listening level.

Each band is cut from pink noise with a one-octave band-pass filter (Q √2). The 31.5 and 63 Hz bands come out weak on small earphones and phone speakers; a high threshold there is a property of the headphones.

Where is the profile used?

The saved profile stays on your device; there is no account and nothing goes to a server. In the Listening room, the ten band gains of the noise layer are filled from this profile; the noise generator uses the same ten bands. The profile changes only the tone balance; it does not change the level, the duration or the limits of the main chain.

Frequently asked questions

Is this a hearing test?
No. The thresholds are set jointly by the headphones, the device setting and the room; no conclusion about your hearing can be drawn. For a hearing question, see an audiologist.
I hear the band even at the quietest level.
Turn the device volume down a little and try the band again; the threshold should fall inside the slider's range.
When should I redo the profile?
When you change headphones or the room changes. The table shows the date of the saved profile; an old profile does not fit new headphones.

· v1.15 · changelog

No cookies, no tracking. Details: Privacy notice (KVKK) On-device storage