02 / Explore · Tools05 / Menu · Tools

Approximate response measurement

See roughly, with a microphone, how strongly your speaker reproduces each frequency. For speakers, not headphones.

Approximate: phone and computer microphones are not calibrated; the result is the combined response of the speaker, the room and the microphone. It is not a sound-pressure or hearing measurement.

The microphone stays open only during the measurement, with echo cancellation and automatic gain requested off. No audio is recorded, stored or sent; only band averages remain on screen.

Measurement

  1. Set the speaker to your normal listening level; start low.
  2. Place the phone or computer facing the speaker, about one metre away.
  3. The measurement takes about 10 seconds: first pink noise plays, then the room's background noise is measured.

Which frequencies is my speaker weak at?

The approximate response measurement plays pink noise through your speaker, listens with the microphone and draws the relative level of 29 one-third-octave bands from 25 Hz to 16 kHz: the curve is the combined response of the speaker, the room and the microphone. There is no calibration; the result is not sound pressure (dB SPL) and not a hearing measurement. The sound is not recorded or sent anywhere.

How to use the approximate response measurement

  1. Set the speaker to your normal listening level and start quietly; measuring with headphones is meaningless, the tool is for speakers.
  2. Put the phone or computer in front of the speaker, about one metre away; press Start measurement and allow microphone access.
  3. The tool averages the spectrum while playing four seconds of pink noise, then measures two seconds of ambient silence and closes the microphone.
  4. Read the curve: values are relative to the median; bands marked 'near ambient' did not rise 10 dB above the room noise and are unreliable.

What is it used for?

  • See your speaker's response in the room

    The tool listens to pink noise through the microphone and draws the relative level in 29 bands: you see which bands swell and which dip.

  • Compare placements

    Take two measurements, moving the speaker closer to or away from the wall or changing where you listen; you see the difference in the bass region on the curve.

  • A starting point for EQ

    The curve gives a rough idea of which band to try cutting on an equaliser; there is no calibration, so the result stays relative and is not sound pressure (dB SPL).

  • Set aside unreliable bands

    In bands marked as close to the room noise, the signal did not rise 10 dB above the background; measure again at a quieter moment. This is not a hearing measurement.

How to read the results

  • The curve's 0 dB line is the median of the bands: +6 dB means that band came in 6 dB stronger than the median, −6 dB 6 dB weaker. A flat curve means the chain passed the pink noise through unchanged in those bands.
  • Faint dots and bands marked NEAR AMBIENT didn't rise 10 dB above the room's silence; the curve skips them, so don't rely on those bands. If there are many, turn the speaker up a little, move the microphone closer or Measure again at a quieter moment.
  • The line under the curve names the first and last reliable bands that are no more than 12 dB below the median: a rough usable range for the speaker. If it says no reliable band was found, background noise is too high.
  • Peaks and dips are the combined response of the speaker, the room and the microphone; you can't tell which one they come from. To compare two measurements, measure from the same spot at the same volume.
  • The curve is relative and uncalibrated: it shows no sound pressure (dB SPL) or hearing value. It means nothing for headphones; the microphone can't hear inside them.

Stages of the measurement

Durations are fixed; the microphone stays open only during the measurement.
StageDurationWhat happens
Settling1.5 spink noise starts, measurement waits
Signal4 sspectrum averaged in 100 ms slices
Tail2 snoise stops, the room decays
Ambient2 ssilence measured, 10 dB limit per band

What does the curve show?

Pink noise carries equal power in every octave; the curve shows how far the spectrum seen by the microphone departs from that expectation. A flat line means the chain passes pink noise unchanged in that band; peaks and dips are the sum of the speaker, the room's reflections and the microphone's own response. The three cannot be separated: the same speaker in another room, or the same room with another microphone, gives another curve.

The summary line gives the frequency range that stays within 12 dB of the median. That range gives a rough idea of the speaker's 'usable band'; with small speakers the low bands stay near the ambient level.

Why not sound pressure?

Phone and computer microphones are not calibrated and the browser cannot know the microphone gain; no absolute level can be read. That is why the tool draws only a relative curve and shows no sound-pressure or hearing value. The microphone is requested with processing off (echo cancellation and automatic gain disabled), and the stream closes as soon as the measurement ends; only the band averages remain on screen.

Frequently asked questions

Can I measure my headphones?
No. The microphone cannot hear inside the headphones; the tool is for the speaker in the room.
Most bands came out 'near ambient'.
The signal did not rise 10 dB above the room noise: turn the speaker up a little, bring the microphone closer or measure at a quieter moment.
Two measurements came out different.
The microphone's position, the furniture in the room and the ambient noise move the curve; measure from the same spot at the same level and compare.

· v1.15 · changelog

No cookies, no tracking. Details: Privacy notice (KVKK) On-device storage