02 / Explore · Tools05 / Menu · Tools

Speaker and stereo test

Are your left and right speakers in the right place, is one wired in reverse, how low does the bass go: check by ear with short signals. Start at a low volume.

Speaker and stereo test

LISTENING FIELDSILENT
STEREO TRIANGLE · ±30°

01 · CHANNEL

02 · POLARITY (BOTH SPEAKERS TOGETHER)

With reversed polarity the sound leaves the centre, spreads around your head and the bass weakens.

03 · SWEEP AND BASS

Start at a low volume; signals fade in gently. In the bass steps, the step where the speaker goes silent or rattles is a rough lower limit. This is not a measurement but a listening check.

Are my speakers wired correctly?

The speaker and stereo test lets you check by ear where your left and right speakers are, whether one is wired with reversed polarity, and how low the bass goes: pink noise from left, centre or right, noise on both speakers in the same or reversed polarity, a 20-second sweep from 20 Hz to 20 kHz, and 20-120 Hz bass steps. The sounds are generated in your browser; it is a listening check, not a measurement.

How do you test your speakers?

  1. Start at a low volume and sit between the speakers, equally far from both (left and right at about 30°).
  2. Tap left, centre and right: does the sound come from the right speaker? Centre should sound between the two.
  3. Compare same and reversed polarity: if same sounds focused in the middle and reversed sounds diffuse and thin, the wiring is correct.
  4. Start the sweep: listen for the frequency where you hear rattling or buzzing as the tone glides from 20 Hz to 20 kHz in 20 seconds.
  5. In the bass steps, the step where the sound disappears or distorts is the speaker's rough lower limit.

What is it used for?

  • Check a new speaker setup

    After placing the left and right speakers, use the channel test to hear that they are connected the right way round and that the centre channel comes from exactly between them.

  • Find a cable wired in reverse

    If plus and minus are swapped on one of the cables, the in-phase noise does not gather in the centre and sounds diffuse and thin in the bass. Comparing it with the reversed-polarity option makes the difference clear.

  • How low does the bass go?

    With the 20-120 Hz bass steps, find by ear the frequency at which your speaker or laptop stops producing bass; it gives a rough idea for the crossover when you set up a subwoofer.

  • Is something rattling in the room?

    If a shelf, a pane of glass or a loose screw buzzes or rattles at some point in the 20 Hz to 20 kHz sweep, you can track down the source. Keep the level low; this is a listening test, not a measurement.

How to read the results

  • The marked source on the triangle is where the sound should come from; the screen doesn't measure what you hear. If LEFT plays from the right, the cables or speakers are swapped; if CENTRE drifts to one side, the levels or distances aren't equal.
  • With SAME POLARITY the triangle draws PHANTOM CENTRE, with REVERSED POLARITY a DIFFUSE IMAGE: that is what you should hear with correct wiring. If you hear the opposite (same polarity diffuse and thin in the bass), one speaker's plus and minus may be swapped.
  • During the SWEEP the Hz value on the triangle is the frequency playing at that moment: the tone glides from 20 Hz to 20 kHz in 20 seconds. Note the number when you hear a click or buzz; the speaker may be struggling at that frequency.
  • On the Bass steps (20, 30, 40, 60, 80, 120 Hz), the step where the sound disappears or distorts is the speaker's rough lower limit. Not hearing the lowest steps is usually not a fault; don't turn the volume up to hear the bass.
  • This is a listening check, not a measurement: the room's reverberation and where you sit change the result. To see the speaker's response as a rough curve, use the approximate response measurement.

What will you hear?

Your room's echo and where you sit can change the result; the check is done by ear.
SignalWhen wired correctlyPossible problem
Left / rightSound comes only from that speakerIf reversed, the cables or speakers have swapped places
CentreOne source between the two speakersIf it leans to one side, levels or distances are not equal
Same polarityFocused in the middle, full bassIf diffuse and thin, one speaker's polarity is reversed
Reversed polarityDiffuse, around your head, weak bassIf it sounds focused, the polarity is already reversed
Bass stepsAudible down to where the speaker can reachRattling or buzzing: the speaker is straining at that frequency

Why does polarity matter?

If a speaker's two terminals (plus and minus) are swapped, its cone moves opposite to the other speaker. When both play the same sound, the waves partly cancel in the air: the sound leaves the centre, spreads around your head, and the bass weakens most.

The test makes this audible: with the same polarity the noise should sit in a focused phantom centre between the speakers, with reversed polarity it should spread. If both sound diffuse, one speaker's cable may be reversed.

Frequently asked questions

Can I use it with headphones?
Left, right and centre work on headphones too, but polarity and the bass steps are meant for speakers. For headphones, the headphone test has left/right, a stereo headphone check and a polarity check.
Does this test measure my speaker's frequency response?
No, it is a listening check. For a rough response with a microphone you can use the approximate response measurement; it is uncalibrated and rough too.
I can't hear the lowest bass step; is my speaker broken?
Most likely not. Most small speakers and laptops don't reproduce below 60-80 Hz, and the ear is less sensitive to very low frequencies. Don't turn the volume up to hear the bass.

· v1.15 · changelog

No cookies, no tracking. Details: Privacy notice (KVKK) On-device storage