Audio file analyzer
An audio file's loudness (LUFS), true peak, RMS, clipping and stereo correlation. The file never leaves this device.
Audio file analyzer
- INTEGRATED
- −24.3 LUFS
- MAX SHORT-TERM
- −21.6 LUFS
- TRUE PEAK
- −13.5 dBTP
- SAMPLE PEAK
- −13.5 dBFS
- RMS
- −26.5 dBFS
- CLIPPING
- 0
- DC OFFSET
- −125 dBFS
- STEREO CORRELATION
- +0.87
The measurement describes the file's signal (ITU-R BS.1770 loudness, true peak with 4× interpolation); it does not show the sound pressure reaching your ears. The file never leaves this device.
How many LUFS is this file, and does it clip?
The audio file analyzer measures an MP3, WAV, FLAC or M4A file's loudness in LUFS (ITU-R BS.1770), its true peak, RMS, clipping, DC offset and stereo correlation, and draws a waveform overview. The file is opened and measured in your browser; it is never sent to a server.
How do you use the audio file analyzer?
- Drag the file onto the drop area, or tap the area and choose the file.
- The file is decoded and measured piece by piece; long files show progress as a percentage.
- In the overview, the faint envelope is the peak and the solid one the RMS; clipped spots are marked at the top.
- Integrated loudness is the average loudness of the whole file; true peak also counts peaks between samples.
- Drop another file to measure again; nothing is kept when you leave the page.
What is it used for?
Check loudness before you publish
Measure the integrated loudness of a podcast or music file in LUFS (ITU-R BS.1770) and its true peak; you see whether it is close to your platform's target.
Find clipping
Clipped spots are marked on the waveform overview; you see whether the sound hit the ceiling in recording or export.
Catch stereo and DC problems
Stereo correlation tells you how similar the channels are, DC offset whether the signal has drifted off the zero line; both are easy to miss when mixing.
Measure an unreleased recording safely
The file is opened and measured in your browser and is never sent to a server; you can check an unreleased recording too.
How to read the results
- The values shown before you drop a file are an example: the first 60 seconds of the Piano in the Rain session. Once you drop your own file, the status line shows its name, and the top of the waveform overview its format, sample rate and length.
- INTEGRATED is the gated average loudness of the whole file (LUFS); very quiet passages are left out. MAX SHORT-TERM is the loudest 3 seconds: if it is far above INTEGRATED, the file has a wide dynamic range.
- TRUE PEAK computes between the samples at four times the rate, so it can read higher than SAMPLE PEAK. A file above −1 dBTP may distort when converted to a lossy format; the site's own limiter also holds peaks at −1 dB.
- If CLIPPING is above 0, warning-coloured marks above the waveform overview show where: at least 3 samples in a row hit the ceiling, and hits closer than 0.1 s count as one spot. The recording or mix may have hit the ceiling.
- A STEREO CORRELATION near +1 means the two channels are almost the same, near 0 means wide; a negative value can point to reversed polarity. MONO means the file has one channel. None of these values shows the sound pressure coming out of a speaker.
Measurements
| Measurement | What it shows | How to read it |
|---|---|---|
| Integrated (LUFS) | Gated average loudness of the whole file (BS.1770) | Most streaming services aim between −14 and −23 LUFS; silent parts are left out. |
| Max short-term | Highest value of a 3-second window | The file's strongest moment; far above integrated means wide dynamics. |
| True peak (dBTP) | Peak between samples, with 4× interpolation | Above −1 dBTP may distort once converted to a lossy format. |
| Sample peak (dBFS) | Largest sample | 0 dBFS is the digital ceiling. |
| RMS (dBFS) | Root mean square of all samples | Unweighted power; unlike LUFS it ignores the ear's sensitivity. |
| Clipping | Spots where at least 3 consecutive samples sit at the ceiling (those closer than 0.1 s count as one) | Above zero, the recording or mix may have hit the ceiling. |
| DC offset | The wave's average offset from zero | Below −60 dBFS it is usually inaudible. |
| Stereo correlation | Similarity of left and right (−1…+1) | +1 is mono-like; near 0 is wide; negative values point to reversed polarity. |
The difference between LUFS and dBFS
dBFS measures the wave's digital size: 0 dBFS is the largest value a sample can take. LUFS is closer to perceived loudness: the signal first passes a K-weighting filter resembling the ear's frequency sensitivity, is then averaged in 400-millisecond blocks, and very quiet blocks are left out (ITU-R BS.1770).
That is why two files with the same peak can measure very differently in LUFS: a compressed song measures high, a dynamic classical recording low.
Why can the true peak be higher than the sample peak?
Digital audio is stored as samples; on playback the space between samples becomes a continuous wave. That wave's peak can fall between two samples and be higher than the largest sample. The analyzer finds it by computing the in-between values four times as densely; our sound engine's limiter uses the same method.
Frequently asked questions
- Is my file uploaded to a server?
- No. The file is decoded and measured in your browser, in your device's memory. It is not sent anywhere and is not kept after you leave the page.
- Which formats can I open?
- Any format your browser can decode: usually WAV, MP3, FLAC, M4A (AAC) and Ogg. Files can be up to 300 MB; larger ones strain memory.
- Why does the measurement differ slightly from another program?
- Lossy formats (MP3, AAC) can decode a few samples differently in each decoder, and programs may compute true peak with different interpolation. Because LUFS uses the BS.1770 gates, it usually agrees within 0.1 LU.
- Does this measurement show the sound is harmless to the ear?
- No. The analyzer measures the file's digital signal; it cannot know your device's volume, speakers or headphones. Start listening at a low volume.
Listen and try
· v1.15 · changelog